--- title: nuttx categories: embedded, arm, stm32, stm32f429 toc: no ... 組員 ---- * 翁振育 * 黃亮穎 * 蘇偉嘉 * 李英碩 hackpad : https://stm32f429.hackpad.com/NuttX--hqco2YSgAcJ Nuttx 參考應用 --------------- * `PX4 autopilot`_ NuttX 架構 ------------ ＊ 可混用task跟thread。 ＊ 支援FPU。 ＊ 可混用FIFO跟RR。 與平台相關 ------------ Run Nuttx on STM32F429-Disco ---------------------------------------------- | (1) 從 https://github.com/deadbeefcafe/nuttx-stm32f4disc-bb 複製Nuttx到workspace | (2) cd workspace/nuttx-stm32f4disc-bb/nuttx/tools | (3) ./configure.sh stm32f429i-disco/nsh | (4) cd .. | (5) make CROSSDEV=arm-none-eabi- | (6) st-flash write nuttx.bin 0x8000000 | (7) sudo screen /dev/ttyUSB0 115200 8n1 設定相關應用程式與功能 ------------------ | at stm32f429i-disco/nsh/defconfig | 120 CONFIG_ARCH_FPU=n | 465 CONFIG_RTC=y | 466 CONFIG_RTC_DATETIME=y | 653 CONFIG_EXAMPLES_HELLO=y | 676 CONFIG_EXAMPLES_OSTEST=y Task Control Interfaces ----------------------- - task_create : 產生一個activates的新task，並回傳系統指派的pid - task_init : 將task的TCB初始化，但並不activate task - task_activate : activate task，否則scheduler沒辦法執行它 - task_delete : 將task關掉，並deallocate它的TCB與stack - task_restart : 將task的children砍掉，deallocate TCB，reset priority - task_exit : 關掉目前在運行的task Task state ------------ include/nuttx/sched.h .. code-block:: c enum tstate_e { TSTATE_TASK_INVALID = 0, /* INVALID - The TCB is uninitialized */ TSTATE_TASK_PENDING, /* READY_TO_RUN - Pending preemption unlock */ TSTATE_TASK_READYTORUN, /* READY-TO-RUN - But not running */ TSTATE_TASK_RUNNING, /* READY_TO_RUN - And running */ TSTATE_TASK_INACTIVE, /* BLOCKED - Initialized but not yet activated */ TSTATE_WAIT_SEM, /* BLOCKED - Waiting for a semaphore */ #ifndef CONFIG_DISABLE_SIGNALS TSTATE_WAIT_SIG, /* BLOCKED - Waiting for a signal */ #endif #ifndef CONFIG_DISABLE_MQUEUE TSTATE_WAIT_MQNOTEMPTY, /* BLOCKED - Waiting for a MQ to become not empty. */ TSTATE_WAIT_MQNOTFULL, /* BLOCKED - Waiting for a MQ to become not full. */ #endif #ifdef CONFIG_PAGING TSTATE_WAIT_PAGEFILL, /* BLOCKED - Waiting for page fill */ #endif NUM_TASK_STATES /* Must be last */ }; Task list ------------ sched/os_internal.h .. code-block:: c typedef struct tasklist_s tasklist_t; extern volatile dq_queue_t g_pendingtasks; extern volatile dq_queue_t g_waitingforsemaphore; #ifndef CONFIG_DISABLE_SIGNALS extern volatile dq_queue_t g_waitingforsignal; #endif #ifndef CONFIG_DISABLE_MQUEUE extern volatile dq_queue_t g_waitingformqnotempty; #endif #ifndef CONFIG_DISABLE_MQUEUE extern volatile dq_queue_t g_waitingformqnotfull; #endif #ifdef CONFIG_PAGING extern volatile dq_queue_t g_waitingforfill; #endif extern volatile dq_queue_t g_inactivetasks; extern volatile sq_queue_t g_delayed_kufree; #if defined(CONFIG_NUTTX_KERNEL) && defined(CONFIG_MM_KERNEL_HEAP) extern volatile sq_queue_t g_delayed_kfree; #endif extern volatile pid_t g_lastpid; extern pidhash_t g_pidhash[CONFIG_MAX_TASKS]; extern const tasklist_t g_tasklisttable[NUM_TASK_STATES]; TCB ------------ include/nuttx/sched.h .. code-block:: c struct tcb_s { /* Fields used to support list management *************************************/ FAR struct tcb_s *flink; /* Doubly linked list */ FAR struct tcb_s *blink; /* Task Management Fields *****************************************************/ pid_t pid; /* This is the ID of the thread */ start_t start; /* Thread start function */ entry_t entry; /* Entry Point into the thread */ uint8_t sched_priority; /* Current priority of the thread */ uint8_t task_state; /* Current state of the thread */ uint16_t flags; /* Misc. general status flags */ int16_t lockcount; /* 0=preemptable (not-locked) */ #if CONFIG_RR_INTERVAL > 0 int timeslice; /* RR timeslice interval remaining */ #endif /* Stack-Related Fields *******************************************************/ #ifndef CONFIG_CUSTOM_STACK size_t adj_stack_size; /* Stack size after adjustment */ /* for hardware, processor, etc. */ /* (for debug purposes only) */ FAR void *stack_alloc_ptr; /* Pointer to allocated stack */ /* Need to deallocate stack */ FAR void *adj_stack_ptr; /* Adjusted stack_alloc_ptr for HW */ /* The initial stack pointer value */ #endif /* POSIX Semaphore Control Fields *********************************************/ sem_t *waitsem; /* Semaphore ID waiting on */ /* POSIX Signal Control Fields ************************************************/ #ifndef CONFIG_DISABLE_SIGNALS sigset_t sigprocmask; /* Signals that are blocked */ sigset_t sigwaitmask; /* Waiting for pending signals */ sq_queue_t sigactionq; /* List of actions for signals */ sq_queue_t sigpendactionq; /* List of pending signal actions */ sq_queue_t sigpostedq; /* List of posted signals */ siginfo_t sigunbinfo; /* Signal info when task unblocked */ #endif /* POSIX Named Message Queue Fields *******************************************/ #ifndef CONFIG_DISABLE_MQUEUE FAR msgq_t *msgwaitq; /* Waiting for this message queue */ #endif /* The form and content of these fields are processor-specific. */ struct xcptcontext xcp; /* Interrupt register save area */ #if CONFIG_TASK_NAME_SIZE > 0 char name[CONFIG_TASK_NAME_SIZE]; /* Task name */ #endif : : : : : : }; Register --------- .. image:: /ARM_register.jpg Communication --------------------- Scheduling ---------------- include/sys/types.h .. code-block:: c /* HPUX-like MIN/MAX value */ #define PRIOR_RR_MIN 0 #define PRIOR_RR_MAX 255 #define PRIOR_FIFO_MIN 0 #define PRIOR_FIFO_MAX 255 #define PRIOR_OTHER_MIN 0 /* Not use */ #define PRIOR_OTHER_MAX 255 /* Not use */ /* Scheduling Priorities. NOTE: Only the idle task can take * the true minimum priority. */ #define SCHED_PRIORITY_MAX 255 #define SCHED_PRIORITY_DEFAULT 100 #define SCHED_PRIORITY_MIN 1 #define SCHED_PRIORITY_IDLE 0 | 1. RR 時間間隔是 20 ticks 做一次 context switch。 | 觀看每個設定time slice的相關檔案其運算是皆為 timeslice = CONFIG_RR_INTERVAL / MSEC_PER_TICK | 在 nuttx/include/nuttx/config.h 中 | CONFIG_RR_INTERVAL = 200 | MSEC_PER_TICK = 10 | 2. 若要禁止 context switch，可用sched_lock() | 此區禁止 context switch | sched_unlock()用在修改scheduler和priority。 | 3. 若要先將 timer interrupt 暫停，可用saved_state = irqsave(); | 此區暫停 timer interrupt | irqrestore(saved_state); | 用在修改 scheduler。 | 注意：timer interrupt 跟 context switch 是不同系統。 | 4. Nuttx 只有兩個 scheduler policy，其 tcb->timeslice = 0 則表示FIFO, 非0則為RR。 Timer interrupt ---------------------- | /nuttx/arch/arm/src/stm32/stm32_vectors.S | | processor exception .. code-block:: c .word IDLE_STACK /* Vector 0: Reset stack pointer */ .word __start /* Vector 1: Reset vector */ .word stm32_nmi /* Vector 2: Non-Maskable Interrupt (NMI) */ .word stm32_hardfault /* Vector 3: Hard fault */ .word stm32_mpu /* Vector 4: Memory management (MPU) */ .word stm32_busfault /* Vector 5: Bus fault */ .word stm32_usagefault /* Vector 6: Usage fault */ .word stm32_reserved /* Vector 7: Reserved */ .word stm32_reserved /* Vector 8: Reserved */ .word stm32_reserved /* Vector 9: Reserved */ .word stm32_reserved /* Vector 10: Reserved */ .word stm32_svcall /* Vector 11: SVC call */ .word stm32_dbgmonitor /* Vector 12: Debug monitor */ .word stm32_reserved /* Vector 13: Reserved */ .word stm32_pendsv /* Vector 14: Pendable system service request */ .word stm32_systick /* Vector 15: System tick */ /nuttx/arch/arm/src/stm32/stm32_timerisr.c (in line 109 ) .. code-block:: c int up_timerisr(int irq, uint32_t *regs) { /* Process timer interrupt */ sched_process_timer(); return 0; } Interrupt handler ------------------------ IRQ numbers .. code-block:: c #define STM32_IRQ_RESERVED (0) /* Reserved vector (only used with CONFIG_DEBUG) */ /* Vector 0: Reset stack pointer value */ /* Vector 1: Reset (not handler as an IRQ) */ #define STM32_IRQ_NMI (2) /* Vector 2: Non-Maskable Interrupt (NMI) */ #define STM32_IRQ_HARDFAULT (3) /* Vector 3: Hard fault */ #define STM32_IRQ_MEMFAULT (4) /* Vector 4: Memory management (MPU) */ #define STM32_IRQ_BUSFAULT (5) /* Vector 5: Bus fault */ #define STM32_IRQ_USAGEFAULT (6) /* Vector 6: Usage fault */ #define STM32_IRQ_SVCALL (11) /* Vector 11: SVC call */ #define STM32_IRQ_DBGMONITOR (12) /* Vector 12: Debug Monitor */ /* Vector 13: Reserved */ #define STM32_IRQ_PENDSV (14) /* Vector 14: Pendable system service request */ #define STM32_IRQ_SYSTICK (15) /* Vector 15: System tick */ FPU ------- | arch/arm/src/armv7-m/up_fpu.S | 儲存 fpu 的 context switch .. code-block:: c up_savefpu: add r1, r0, #(4*REG_S0) /* R1=Address of FP register storage */ /* Some older GNU assemblers don't support all the newer UAL mnemonics. */ #if 1 /* Use UAL mnemonics */ /* Store all floating point registers. Registers are stored in numeric order, * s0, s1, ... in increasing address order. */ vstmia r1!, {s0-s31} /* Save the full FP context */ /* Store the floating point control and status register. At the end of the * vstmia, r1 will point to the FPCSR storage location. */ vmrs r2, fpscr /* Fetch the FPCSR */ str r2, [r1], #4 /* Save the floating point control and status register */ #else /* Store all floating point registers */ #if 1 /* Use store multiple */ fstmias r1!, {s0-s31} /* Save the full FP context */ #else vmov r2, r3, d0 /* r2, r3 = d0 */ str r2, [r1], #4 /* Save S0 and S1 values */ str r3, [r1], #4 vmov r2, r3, d1 /* r2, r3 = d1 */ str r2, [r1], #4 /* Save S2 and S3 values */ str r3, [r1], #4 vmov r2, r3, d2 /* r2, r3 = d2 */ str r2, [r1], #4 /* Save S4 and S5 values */ str r3, [r1], #4 vmov r2, r3, d3 /* r2, r3 = d3 */ str r2, [r1], #4 /* Save S6 and S7 values */ str r3, [r1], #4 vmov r2, r3, d4 /* r2, r3 = d4 */ str r2, [r1], #4 /* Save S8 and S9 values */ str r3, [r1], #4 vmov r2, r3, d5 /* r2, r3 = d5 */ str r2, [r1], #4 /* Save S10 and S11 values */ str r3, [r1], #4 vmov r2, r3, d6 /* r2, r3 = d6 */ str r2, [r1], #4 /* Save S12 and S13 values */ str r3, [r1], #4 vmov r2, r3, d7 /* r2, r3 = d7 */ str r2, [r1], #4 /* Save S14 and S15 values */ str r3, [r1], #4 vmov r2, r3, d8 /* r2, r3 = d8 */ str r2, [r1], #4 /* Save S16 and S17 values */ str r3, [r1], #4 vmov r2, r3, d9 /* r2, r3 = d9 */ str r2, [r1], #4 /* Save S18 and S19 values */ str r3, [r1], #4 vmov r2, r3, d10 /* r2, r3 = d10 */ str r2, [r1], #4 /* Save S20 and S21 values */ str r3, [r1], #4 vmov r2, r3, d11 /* r2, r3 = d11 */ str r2, [r1], #4 /* Save S22 and S23 values */ str r3, [r1], #4 vmov r2, r3, d12 /* r2, r3 = d12 */ str r2, [r1], #4 /* Save S24 and S25 values */ str r3, [r1], #4 vmov r2, r3, d13 /* r2, r3 = d13 */ str r2, [r1], #4 /* Save S26 and S27 values */ str r3, [r1], #4 vmov r2, r3, d14 /* r2, r3 = d14 */ str r2, [r1], #4 /* Save S28 and S29 values */ str r3, [r1], #4 vmov r2, r3, d15 /* r2, r3 = d15 */ str r2, [r1], #4 /* Save S30 and S31 values */ str r3, [r1], #4 #endif /* Store the floating point control and status register */ fmrx r2, fpscr /* Fetch the FPCSR */ str r2, [r1], #4 /* Save the floating point control and status register */ #endif bx lr .size up_savefpu, .-up_savefpu | 載回 fpu 的 context switch .. code-block:: c up_restorefpu: add r1, r0, #(4*REG_S0) /* R1=Address of FP register storage */ /* Some older GNU assemblers don't support all the newer UAL mnemonics. */ #if 1 /* Use UAL mnemonics */ /* Load all floating point registers. Registers are loaded in numeric order, * s0, s1, ... in increasing address order. */ vldmia r1!, {s0-s31} /* Restore the full FP context */ /* Load the floating point control and status register. At the end of the * vstmia, r1 will point to the FPCSR storage location. */ ldr r2, [r1], #4 /* Fetch the floating point control and status register */ vmsr fpscr, r2 /* Restore the FPCSR */ #else /* Load all floating point registers Registers are loaded in numeric order, * s0, s1, ... in increasing address order. */ #if 1 /* Use load multiple */ fldmias r1!, {s0-s31} /* Restore the full FP context */ #else ldr r2, [r1], #4 /* Fetch S0 and S1 values */ ldr r3, [r1], #4 vmov d0, r2, r3 /* Save as d0 */ ldr r2, [r1], #4 /* Fetch S2 and S3 values */ ldr r3, [r1], #4 vmov d1, r2, r3 /* Save as d1 */ ldr r2, [r1], #4 /* Fetch S4 and S5 values */ ldr r3, [r1], #4 vmov d2, r2, r3 /* Save as d2 */ ldr r2, [r1], #4 /* Fetch S6 and S7 values */ ldr r3, [r1], #4 vmov d3, r2, r3 /* Save as d3 */ ldr r2, [r1], #4 /* Fetch S8 and S9 values */ ldr r3, [r1], #4 vmov d4, r2, r3 /* Save as d4 */ ldr r2, [r1], #4 /* Fetch S10 and S11 values */ ldr r3, [r1], #4 vmov d5, r2, r3 /* Save as d5 */ ldr r2, [r1], #4 /* Fetch S12 and S13 values */ ldr r3, [r1], #4 vmov d6, r2, r3 /* Save as d6 */ ldr r2, [r1], #4 /* Fetch S14 and S15 values */ ldr r3, [r1], #4 vmov d7, r2, r3 /* Save as d7 */ ldr r2, [r1], #4 /* Fetch S16 and S17 values */ ldr r3, [r1], #4 vmov d8, r2, r3 /* Save as d8 */ ldr r2, [r1], #4 /* Fetch S18 and S19 values */ ldr r3, [r1], #4 vmov d9, r2, r3 /* Save as d9 */ ldr r2, [r1], #4 /* Fetch S20 and S21 values */ ldr r3, [r1], #4 vmov d10, r2, r3 /* Save as d10 */ ldr r2, [r1], #4 /* Fetch S22 and S23 values */ ldr r3, [r1], #4 vmov d11, r2, r3 /* Save as d11 */ ldr r2, [r1], #4 /* Fetch S24 and S25 values */ ldr r3, [r1], #4 vmov d12, r2, r3 /* Save as d12 */ ldr r2, [r1], #4 /* Fetch S26 and S27 values */ ldr r3, [r1], #4 vmov d13, r2, r3 /* Save as d13 */ ldr r2, [r1], #4 /* Fetch S28 and S29 values */ ldr r3, [r1], #4 vmov d14, r2, r3 /* Save as d14 */ ldr r2, [r1], #4 /* Fetch S30 and S31 values */ ldr r3, [r1], #4 vmov d15, r2, r3 /* Save as d15 */ #endif /* Load the floating point control and status register. r1 points t * the address of the FPCSR register. */ ldr r2, [r1], #4 /* Fetch the floating point control and status register */ fmxr fpscr, r2 /* Restore the FPCSR */ #endif bx lr .size up_restorefpu, .-up_restorefpu #endif /* CONFIG_ARCH_FPU */ | /nuttx/arch/arm/include/armv7-m/irq.h | struct xcptcontext | /nuttx/arch/arm/include/armv7-m/irq_lazyfpu.h | XCPTCONTEXT_REGS = HW_XCPT_REGS + SW_XCPT_REGS | XCPTCONTEXT_SIZE = 4 * XCPTCONTEXT_REGS 測試環境架設 ------------ 硬體驅動原理 ------------ * `UART`_ * FPU (Floating Point Unit) 效能表現 -------- 參考資料 -------- * https://github.com/deadbeefcafe/nuttx-stm32f4disc-bb * http://bibliodigital.itcr.ac.cr/xmlui/bitstream/handle/2238/3051/FinalReport.pdf